报警探头生产厂家

GSM商用/家用报警器
GSM无线报警器是本公司研制、生产的新系列商用/家用安全防范报警系统，采用单片机和无线遥控技术，系统更加可靠、安装操作更简便。该产品基于现有的GSM网络远程报警，该系统具有探测灵敏，抗干扰强，报警准确可靠，安装、操作简便等优点，是一种实用新型的家用/商用防盗产品！
ATS-GM802GSM报警主机功能参数：
1.系统采用故态记忆系统,掉电后也无须重新设置
2. 有8个无线防区,2个有线防区,可连接任何探测器,例如红外感应,门磁,烟感,燃气探测器,紧急按扭.
3. 可通过手机短信和电话远程控制家电开关,布防/撤防,
4．远程主动 功能： 在设定的条件下，可以实现 声音功能；
5.通过GSM平台与报警中心联网
6.外置高分贝警号可威吓非法入侵者
7.可通过密码布撤防
8.可设置5组报警号码,报警可直接和控制中心,警察局,或您和您的朋友联系
9、GSM报警主机采用高品质专业GSM模块精心设计。
10、无线系统，不用布线施工，安装简便快捷。
11、通过GSM无线网络报警。
12、报警现场监听功能：输入正确密码后，在报警监听范围内，能清晰地听到现场作案者的语音、人走动、挖、撬等动作声音；能远程通过电话遥控延长或提前结束监听时间及监听情况下撤防。
13、可配各种无线防盗探测器、红外对射栅栏、烟感、煤气感、、紧急按钮。
14、通过无线遥控器，控制该系统布防、撤防或紧急报警，使用户在实际使用中方便快捷。
15、密码操作，确保系统安全：可通过异地电话密码遥控布防和撤防。
16、无线远程遥控布警/消警，真正的无延迟报警。报警发生后，有远程布/撤防功能，主人在输入正确密码后，能远程通过电话或手机对系统进行布/撤防控制。
17、智能识别主人是否接警，一旦接警，不再拨打该号码。
18、主人能远程通过电话遥控，三路输出控制房间灯光、空调开关、电饭煲等。
19、具有三路有线输入控制端，方便连接各种有线探头。
20、主机具有报警时继电器输出控制端，方便可联动电源、录像等工作。
整个系统可供防盗、防抢劫、防火、防流氓滋扰、防诈骗等全方位警情处理。

GSM报警主机技术参数：
1、主机盒装（长*宽*高）：85 x 45 x 25mm。
2、使用环境条件：室内，环境温度-10 ~ 50℃，相对湿度≤90%，大气压力86 ~106Kpa。
3、报警接收方式：FSK，接收距离100-250米。
4、报警方式：GSM网络传输报警，短信报警。
5、储存电话号码：5组，电话号码位长：32位。
6、工作频率：315MHz/433MHz。
标准配置：标准配置：GSM报警主机一台、警号一只、电源一只、遥控器两只、天线一条。
可选配：无线烟感探头、无线燃气探头、无线红外对射、卷闸门无线传感器、无线紧急按钮、信号中继器等。

英文说明：

This is GSM Alarm system for household/Business office security.
Multi-sensors detecting for more security.
Wireless communication, no need wire connection and easy installation
Learning code,easy to learn and promote.

--------------------------------------------------------------------------------
1. Is a one-zone alarm system, very suitable for small office and home appliance!
2. Alarm system uses a GSM communicator, so is no distance limits to receive alarms or dial out to control the alarm system.
3. System can support GSM/CDMA cell phones.
4. Can store and dial 5 phone numbers (no longer than 16 character each one). If an alarm occurs,    numbers will be dialed in order starting with last stored. You can set to dial monitoring center, police and owners.
5. Using remote controllers you can arm, disarm, panic from long distance.
6. You can control the system by using a telephone anytime, wherever you are. For security reasons a PIN code must be used for access.
7.Supports all kinds of wireless sensors, such as PIR detectors, door (gap) sensors, gas sensors, smoke sensors; panic buttons and infrared balusters are available.
8. Supports any wired sensors available (NC contacts)
9. Supports any combination of wired/wireless sensors, as you need.
10.No need for fixed telephone line. Is very suitable for cottage, house, shop, garage, everywhere a GSM Network is present.
11. For weak GSM signal area an external antenna can be used.
12. Three open collector outputs available to be used according to customer demands
13. One onboard relay available for customer application.
14. Easy to be installed and operated according to the instructions from this manual.
15. CE & FCC approved
--------------------------------------------------------------------------------

Parameter:
Power supply: Input AC 110V; 220V; 230—240V, 50/60HZ; Output DC 12V, 1000mA
Frequency: 315MHz/433MHz 
GSM receiving:  900/1800mhz
Stand-by current: ≤ 20mA 
Alarm current: ≤ 150mA 
Operating range: up to 100 meters in open place
Siren: ≥ 110db 
Temperature range:-10 ~ 50 ℃ 
Relative humidity: ≤ 90%
Dimension: 34x 22 x 32cm (Gift box)
Net weight: 1.2kg

--------------------------------------------------------------------------------

Attention!  Be careful, do not over-tighten the nut or let it loose!
Installation guide:
Basic Kit contains:
-Alarm system (control unit) – 1 pc.
-Wireless PIR detector – 1 pc.
-Wireless door (gap) sensor – 1 pc.
-Remote controller – 2 pc.
-Antenna – 1pc.
-Mini wired siren 110dB/0.3m – 1 pc.
-Power supply with back-up – 1pc.
-Installation/user manual – 1pc

1. Insert SIM in alarm unit.
Press yellow point gently with a pencil tip. SIM tray will come out.
Put the SIM in it and insert in back.
Attention! Metal contacts of the SIM must be down. Check it to be inserted correctly in the unit.
Before insert SIM in alarm unit, using a regular mobile phone do the following steps:
- Set PIN code request to off.
- Delete all stored numbers
- Store only numbers desired for alarming (up to 5 numbers). Numbers must be inserted in order of calling. First stored will be first called, second stored will be second called and so on.

2. Connect the antenna.
Attention!  Be careful, do not over-tighten the nut or let it loose!

3.Connect the siren to alarm system: connect red wire to ground(public) port and black wire to siren port.

4.How to distinguish 8 LEDs on the main panel?

OUT1, OUT 2 and OUT 3:  show the status of output 1,2 and 3. They can be used to three lights or other home appliances.
RELAY: The fourth LED. It shows relay status. There is a on-board relay inside. The Relay LED will be on when the relay’s two ports are closed.
ALARM: The fifth LED shows the working status of siren. If siren is triggered, the “Alarm” LED will be on.
MONITOR: When it is on, it means the system is in the status of listening-in.
STATUS: It shows the signal status. At the first beginning, it is red which shows that the system is searching for GSM network and it will turn green when it finds GSM network. At this moment, the GSM alarm system is ready to work.
POWER: Power status LED. It will be on when the system is switched on.
If you use only kit sensors, system is ready to be power on.
Sensors and remote controls delivered in kit are already coded (registered) in the system by factory. Plug in DC 12V power supply in alarm system.

Using a telephone or cell phone to make GSM Alarm system arm/disarm:

Call the alarm system. After one ring unit will answer and a beep will be heard.
You have to input a PIN and # at end for security purpose. Default PIN is 1234.
At first login, please dial 1234#.
NOTICE! This PIN code is for alarm system NOT for SIM card.
System responds with beep (digital voices are available for some areas) and now you can send several commands and change some settings.
Commands of the system:

a. 1# - set output 1(open collector) on
b. 1* - set output 1 off
c. 2# - set output 2(open collector) on
d. 2* - set output 2 off
e. 3# - set output 3(open collector) on
f. 3* - set output 3 off
g. 4# - set output 4(onboard relay) on
h. 4* - set output 4 off
i. 5#- set Text message (SMS) on (default)
j. 5*- set Text message off
k. 6# - set with voice
l. 6* - set voice off
m. 7# - set alarm siren to work (default)
n. 7* - set siren all time off (silent alarm)
o. 8#abcd# -set new PIN. E.g.: 8#8686# --set new PIN code at 8686.
Note: It is wise to change PIN code at first login in alarm system.
p. 9* - stop the siren and open internal microphone of alarm system, for audio
monitoring of the spot.
q. 9# - stop monitoring/listening-in and open the siren
r. 0# - arm the system
s. 0* - disarm the system

Advanced Instructions

1. Resetting the system.
NOTICE! Resetting the system all coded information and messages will be lost.
System will be loaded with basic factory settings. The passwords will be back to
the original default-1234.  You must code/register all wireless sensors again after reset.

Reset procedure:
- System must be disarmed
- Press reset button and keep it pressed
- Plug off 12V supply from alarm system
- Plug on 12V supply at alarm system again, alarm LED will have a brief flash
- Release reset button and let system LED to become green.
Now system is reset and back to factory settings.(the passwords is 1234)

2. Coding wireless sensors. (Registering wireless sensors with control unit)
Procedure to add a new sensor (remote controller/wireless door sensor, wireless PIR detectors) in the system:
- Plug off 12V supply from alarm system
- Plug on 12V supply at alarm system
STATUS light will be red for 20 seconds. During this time make sensors to work (press any button on remote controller, make PIR and gap sensors (move the two parts of door sensor) to work). They will be recognized and coded in the system. After 20s system is ready to work when the Status light turns green.

Test all sensors and repeat procedure for any sensor, if is necessary.
Maximum number of wireless sensors that can be coded by system is 10. But you can register countless wireless sensors by changing sensors’ ID.

About sales:

Note: We sell at a standard pack(Basic Kit). It includes:
Basic Kit contains:
- Alarm system (control unit) – 1 pc.
- Wireless PIR detector – 1 pc.
- Wireless door (gap) sensor – 1 pc.
- Remote controller – 2 pc.
- Antenna – 1pc.
- Mini wired siren 110dB/0.3m – 1 pc.
- Power supply with back-up – 1pc.
- Installation/user manual – 1pc

Additional wireless products

PIR Detectors / Smoke Detectors  /  Panic Buttons  /  Door/Window  gap sensors   /   Remote Cotrols   /  LPG Gas Detectors

Optional sensors/detectors are packed separately. It inclodes remote controlles,
wireless PIR, wireless gap sensor, wireless gas detector,wireless smoke detector,
panic button,baluster,according your specific needs.